Link-state routing protocol
|
|
A Link-state routing protocol is one of the two main classes of routing protocols used in packet-switched networks for computer communications.
The link-state protocol is performed by every switching node in the network (i.e. nodes which are prepared to forward packets; in the Internet, these are called routers). The basic concept of link-state routing is that every node receives a map of the connectivity of the network, in the form of a graph showing which nodes are connected to which other nodes.
Each node then independently calculates the best next hop from it for every possible destination in the network. (It does this using only its local copy of the map, and without communicating in any other way with any other node.) The collection of best next hops forms the routing table for the node.
This contrasts with distance-vector routing protocols, which work by having each node share its routing table with its neighbors. In a link-state protocol, the only information passed between the nodes is information used to construct the connectivity maps.
| Contents |
History
The first network to use a link-state routing protocol was the ARPANET, after the initial distance-vector routing protocol proved to have a number of major problems, once placed in service.
Link-state routing was invented in 1978 by John McQuillan, then at Bolt, Beranek and Newman, as a mechanism that would calculate routes more quickly when network conditions changed, and thus lead to more stable routing.
Later work at BBN showed how to use the link-state technique in a hierarchical system, i.e. one in which the network was divided into areas, so that each switching node does not need a map of the entire network, only the area(s) in which it is included.
The technique was later adapted for use in the contemporary link-state routing protocols IS-IS and OSPF.
Note: The impression in various Cisco marketing documents to the contrary, EIGRP is definitely not a link-state protocol, or any sort of "hybrid" thereof.
More recently, this technique was applied to wireless mesh networks using the optimized link state routing protocol.
Detailed description: Distributing maps
This description covers only the simplest configuration; i.e. one with no areas, so that all nodes do have a map of the entire network. The hierarchical case is somewhat more complex; see the various protocol specifications.
As previously mentioned, the first main stage in the link-state algorithm is to give a map of the network to every node. This is done with several simple subsidiary steps.
Determining the neighbours of each node
First, each node needs to determine what other nodes it is connected to, over fully-working links; it does this using a simple reachability protocol which it runs separately with each of its directly-connected neighbours.
Distributing the information for the map
Next, each node periodically makes up a short message, the link-state advertisement, which:
- Identifies the node which is producing it.
- Identifies all the other nodes to which it is directly connected.
- Includes a sequence number, which increases every time the source node makes up a new version of the message.
This message is then flooded throughout the network. As a necessary precursor, each node in the network remembers, for every other node in the network, the sequence number of the last link-state message which it received from that node. With that in hand, the method used is simple.
Starting with the node which originally produced the message, it sends a copy to all of its neighbours. When a link-state advertisement is received at a node, the node looks up the sequence number it has stored for the source of that link-state message. If this message is newer (i.e. has a higher sequence number), it is saved, and a copy is sent in turn to each of that node's neighbours.
This procedure rapidly gets a copy of the latest version of each node's link-state advertisement to every node in the network.
Creating the map
Finally, with the complete set of link-state advertisements (one from each node in the network) in hand, it is obviously easy to produce the graph for the map of the network.
The algorithm simply iterates over the collection of link-state advertisements; for each one, it makes links on the map of the network, from the node which sent that message, to all the nodes which that message indicates are neighbours of the sending node.
No link is considered to have been correctly reported unless the two ends agree; i.e. if one node reports that it is connected to another, but the other node does not report that it is connected to the first, there is a problem, and the link is not included on the map.
Notes about this stage
The link-state message giving information about the neighbours is recomputed, and then flooded throughout the network, whenever there is a change in the connectivity between the node and its neighbours, e.g. when a link fails. Any such change will be detected by the reachability protocol which each node runs with its neighbours.
Detailed description: Calculating the routing table
As initially mentioned, the second main stage in the link-state algorithm is to produce routing tables, by inspecting the maps. This is again done with several steps.
Calculating the shortest paths
Each node independently runs an algorithm over the map to determine the shortest path from themselves to every other node in the network; generally some variant of Dijkstra's algorithm is used.
Basically, a node maintains two data structures: a tree containing nodes which are "done", and a list of candidates. The algorithm starts with both structures empty; it then adds to the first one the node itself. The algorithm then repetitively:
- Adds to the second (candidate) list all nodes which are connected to the node just added to the tree (excepting of course any nodes which are already in either the tree or the candidate list).
- Of the nodes in the candidate list, moves to the tree (attaching it to the appropriate neighbour node already there) the one which is the closest to any of the nodes already in the tree.
- Repeat as long as there are any nodes left in the candidate list. (When there are none, all the nodes in the network will have been added to the tree.)
This procedure ends with the tree containing all the nodes in the network, with the node on which the algorithm is running as the root of the tree. The shortest path from that node to any other node is indicated by the list of nodes one traverses to get from the root of the tree, to the desired node in the tree.
Filling the routing table
With the shortest paths in hand, filling in the routing table is again obviously easy.
For any given destination node, the best next hop for that destination is the node which is the first step from the root node, down the branch in the shortest-path tree which leads toward the desired destination node.
To create the routing table, it is only necessary to walk the tree, remembering the identity of the node at the head of each branch, and filling in the routing table entry for each node one comes across with that identity.
Optimizations
The algorithm described above was made as simple as possible, to aid in ease of understanding. In practise, there are a number of optimizations which are used.
Most importantly, whenever a change in the connectivity map happens, it is necessary to recompute the shortest-path tree, and then recreate the routing table. The BBN work discovered how to recompute only that part of the tree which could have been affected by a given change in the map.
Also, the routing table would normally be filled in as the shortest-path tree is computed, instead of making it a separate operation.
Notes
If all the nodes are not working from exactly the same map, routing loops can form. (These are situations in which, in the simplest form, two neighbouring nodes each think the other is the best next hop to a given destination. Any packet headed to that destination arriving at either node will loop between the two, hence the name. Routing loops involving more than two nodes are also possible.)
The reason is fairly simple: since each node computes its shortest-path tree, and its routing table, without interacting in any way with any other nodes, if two nodes start with different maps it is easy to have scenarios in which routing loops are created.
Advantages and disadvantages of link-state routing
The primary advantage of link-state routing is that it reacts more quickly, and in a bounded amount of time, to connectivity changes. The primary disadvantage of link-state routing is that it requires more storage and more computing to run than does distance-vector routing.