Tesla coil

A Tesla coil is a category of disruptive discharge coils, named after their inventor, Nikola Tesla. Tesla actually experimented with a large variety of coils and configurations, so it is difficult to describe a specific mode of construction that will meet the wants of those who ask about "Tesla" coils. It is widely known that Tesla coils are composed of coupled resonant circuits.

Contents

Introduction

Early coils

The American Electrician gives a description of one wherein a glass battery jar, six inches by eight inches, is wound with 60 to 80 turns of No. 18 B & S magnet wire. Into this is slipped a primary consisting of eight to ten turns of No. 6 B & S wire, and the whole combination immersed in a vessel containing linseed or mineral oil. (Norrie, pg. 34-35)

Disruptive "Tesla" Coils

Following the initial research of voltage and frequency by William Crookes, Tesla developed a series of coils that produced high-voltage, high-frequency currents. In the majority of Tesla's experiments, he used machinery of his own design to produce the Tesla effect. These early coils would use the "disruptive" action of a spark gap in their operation. The setup can be duplicated by a Ruhmkorff coil, two condensers, and a second, specially constructed, disruptive coil. (Norrie, pg. 228)

The Ruhmkorff coil, being fed from a main source, is wired to condensers (now called capacitors) on both ends in series. A spark gap is placed in parallel to the Ruhmkorff coil before the condensers. The discharge tips usually preferably metal balls under one inch in diameter, though Tesla used various forms of dischargers. The condensers were of a special design, small with high insulation. These condensers consisted of plates in oil that were movable. The smaller the plates, the more frequent the discharge of this early coil apparatus. The plates also help nullify the high self inductance of the secondary coil by adding capacity to it. Mica plates were placed in the spark gap to establish a air current jet to go up through the gap. This made the discharge more abrupt. An air blast was also used for this objective. (Norrie, pg. 230-231)

The condensers are connected to a double primary (each coil in series with a condenser). These are part of the second specially constructed disruptive coil. The primaries each have twenty turns of No. 16 B & S rubber covered wire and are wound separately on a rubber tubes not less than a 1/8th inch thick. The secondary has 300 turns of No. 30 B & S silk-covered magnet wire, wound on rubber tube or rod, and the eneds encased in glass or rubber tubes. The primaries must be large enough to be loose when the secondary coil is place between the coils. The primaries must cover around two inches of the secondary. A hard rubber division must be placed between these primary coils. The ends of the primaries not connected with the condensers are lead to a spark gap. (Norrie, pg. 35-36)

Tesla's later coils were considerably larger and operated at much higher power levels. These later systems were powered from large high voltage transformers, used banks of glass bottle capacitors immersed in oil to reduce corona losses, and used rotating spark gaps to handle the higher power levels. Tesla also dispensed with using oil to insulate the transformer coils, relying instead on the insulating properties of air. Tesla coils achieve great gain in voltage by loosely coupling two resonant LC circuits together, using an air-core (ironless) transformer. Unlike a conventional transformer, whose gain is limited to the ratio of the numbers of turns in the windings, Tesla coils' voltage gain is proportional to the square root of the ratio of secondary and primary inductances.

Later coils

View in elevationFree terminal and circuit of large surface with supporting structure and generating apparatus
Enlarge
View in elevation
Free terminal and circuit of large surface with supporting structure and generating apparatus

When Tesla patented a later device (US1119732 — Apparatus for Transmitting Electrical Energy), he called it a high-voltage, air-core, self-regenerative resonant transformer that generates very high voltages at high frequency. However, this phrase is no longer in conventional use.

This later coil type is the usual device built by modern enthusiasts. It is an air-core, dual-tuned resonant transformer that generates very high voltages at radio frequencies. The coil achieves a great gain in voltage by means of a resonant circuit, unlike a conventional transformer whose gain is limited to the ratio of the numbers of turns in the windings. The Tesla coil's outer conducting surfaces, which are charged to a high potential, have large radii of curvature to minimise leakage of the oscillating charge.

Although modern Tesla Coils are designed to generate long sparks, Tesla's orignal system were designed for wireless communication and power transmission, so he used large radii of curvature to prevent corona and streamer losses. Tesla coils' outer conducting surfaces, which are charged to a high potential, have large radii of curvature to minimise leakage of the oscillating charges through corona discharges or sparks. The intensity of the voltage gain of the circuit with a free, or elevated, toroid is proportional to the quantity of charge displaced, which is determined by the product of the capacitance of the circuit, the voltage (which Tesla called "pressure"), and the frequency of the currents employed.

Description

Later coils consist of a primary tank circuit, which is a series LC circuit composed of a high voltage capacitor, spark gap, and primary coil; and the secondary LC circuit, a series resonant circuit consisting of the secondary coil and the toroid. In Tesla's orginal plans, the secondary LC circuit is composed of a loaded secondary coil which is then placed in series with a large helical coil. The helical coil is then connected to the toroid. The toroid actually forms one terminal of a capacitor, the other terminal being the Earth (or "ground"). The primary LC circuit is "tuned" so that it will resonate at the same frequency as the secondary LC circuit. The primary and secondary coils are magnetically coupled, creating a dual-tuned resonant air-core transformer.

The terminal consists of a metallic frame, sometimes a circular ring covered with smooth half spherical metal plates (constituting a very large conducting surface). The terminal has relatively small capacitance, charged to as high a voltage as practicable. The outer surface of the elevated conductor is where the electrical charge chiefly accumulates. It has a large radius of curvature, or is composed of separate elements which, irrespective of their own radii of curvature, are arranged close to each other so that the outside ideal surface enveloping them has a large radius.

The frame is carried by a strong platform and rests on insulating supports. The circuit consists of a coil in close inductive relation with a primary, and one end of which is connected to a ground-plate, while its other end is led through a separate self-induction coil (whose connection should always be made at, or near, the center in order to secure a symmetrical distribution of the current) and a metallic cylinder to the terminal. The primary coil may be excited by any desired source. The important requirement is that a resonant condition be established. A high frequency alternator or a capacitor discharge can be used to excite the primary coil.

The conductor of the shaft to the terminal is in the form of a cylinder with smooth surface of a radius much larger than that of the spherical metal plates, and widens out at the bottom into a hood (which is slotted to avoid loss by eddy currents and for safety). The secondary coil is wound on a drum of insulating material, with its turns close together. When the effect of the small radius of curvature of the wire itself is overcome, the lower secondary coil behaves as a conductor of large radius of curvature, corresponding to that of the drum (this effect is applicable elsewhere). The lower end of the upper secondary coil, if desired, may be extended up to the terminal and should be somewhat below the uppermost turn of the primary coil. This lessens the tendency of the charge to break out from the wire connecting both and to pass along the support.

Utilization and production

Missing image
TCOIL3.png
Typical Tesla Coil Schematic
This example circuit is designed to be driven by alternating currents.

Transmission

A large Tesla coil of more modern design can operate at very high peak power levels, up to many megawatts (or hundreds of thousands of horsepower). It should therefore be adjusted and operated carefully, not only for efficiency and economy, but also for safety. If, due to improper tuning, the maximum voltage point occurs below the terminal, along the secondary coil, a discharge (spark), or possibly a ball of plasma, may break out and damage or destroy the coil wire, supports, nearby objects, or anything else in the way.

Safety and precautions

It is advisable to begin the tuning, in which the primary coil's resonant frequency is set to the same value of the secondary coil's, using low-power and low-frequency oscillations, then increasing the power and frequency until the apparatus has been brought under control. While tuning, a small projection (called a "breakout bump") may be added to the top terminal in order to stimulate corona and spark discharges (sometimes called streamers) into the surrounding air. One or more elements or plates of somewhat smaller radius of curvature or protruding more or less beyond the others (in which case they may be of larger radius of curvature) so that, should the voltage rise too high, the powerful discharge may escape to the air. Tuning can then be adjusted so as to get the longest streamers at a given power level, if desired. For a variety of technical reasons, toroids provide the best overall shape for top terminals of modern Tesla coils.

Since Tesla coils can produce currents or discharges of very high frequency and voltage, they are useful for various purposes including classroom demonstration, theater and movie special-effects, and product/technology safety testing. In typical operation, long, branching high-voltage sparks may strike out in all directions from the toroid into the air, producing a dangerous, yet strangely beautiful, lightning-like display of electricity "in action".

Air Discharges

While generating discharges, electrical energy from the secondary and toroid is transferred to the surrounding air as electrical charge, heat, light, and sound. The electric currents that flow through these discharges are actually due to the rapid shifting of quantities of charge from one place (the top terminal) to other places (nearby regions of air). The process is similar to charging or discharging a capacitor. The current that arises from shifting charges within a capacitor is called a displacement current. Tesla Coil discharges are formed as a result of displacement currents as pulses of electrical charge are rapidly transferred between the high voltage toroid and nearby regions within the air (called space charge regions). Although the space charge regions around the toroid are invisible, they play a profound role in the appearance and location of Tesla Coil discharges.

When the spark gap fires, the charged capacitor discharges into the primary winding, causing the primary circuit to oscillate. The oscillating primary current creates a magnetic field that couples to the secondary winding, transferring energy into the secondary side of the transformer and causing it to oscillate with the toroid capacitance. The energy transfer occurs over a number of cycles, and most of the energy that was originally in the primary side is transferred into the secondary side. The greater the magnetic coupling between windings, the shorter the time required to complete the energy transfer. As energy builds within the oscillating secondary circuit, the amplitude of the toroid's RF voltage rapidly increases, and the air surrounding toroid begins to undergo dielectric breakdown, forming a corona discharge.

As the secondary's energy (and output voltage) continue to increase, larger pulses of displacement current further ionize and heat the air at the point of initial breakdown. This forms a very conductive "root" of hotter plasma, called a leader, that projects outward from the toroid. The plasma within the leader is considerably hotter than a corona discharge, and is considerably more conductive. In fact, it has properties that are similar to an electric arc. The leader tapers and branches into thousands of thinner, cooler, hairlike discharges (called streamers). The streamers look like a bluish "haze" at the ends of the more luminous leaders, and it's the streamers that actually transfer charge between the leaders and toroid to nearby space charge regions. The displacement currents from countless streamers all feed into the leader, helping to keep it hot and electrically conductive.

In a spark gap Tesla Coil the primary-to-secondary energy transfer process happens repetitively at typical pulsing rates of 50–500 times/second, and previously formed leader channels don't get a chance to fully cool down between pulses. So, on successive pulses, newer discharges can build upon the hot pathways left by their predecessors. This causes incremental growth of the leader from one pulse to the next, lengthenning the entire discharge on each successive pulse. Repetitive pulsing causes the discharges to grow until the average energy that's available from the Tesla Coil during each pulse balances the average energy being lost in the discharges (mostly as heat). At this point, dynamic equilibrium is reached, and the discharges have reached their maximum length for the Tesla Coil's output power level. The unique combination of a rising high voltage Radio Frequency envelope and repetitive pulsing seem to be ideally suited to creating long, branching discharges that are considerably longer than would otherwise be expected by output voltage considerations alone. However, even 100 years later, there are many aspects of Tesla Coil discharges and the energy transfer process that are still not completely understood.

Reception

The secondary coil and its capacitor can be used in receive mode. Generally, though, Tesla coils are not used for these purposes. Theoretically, a variation of the Tesla coil could utilize the phantom loop effect to form a circuit to induct energy from the earth's magnetic field. This concept is part of Tesla's wireless transmission of electric power distribution system (US1119732 — Apparatus for Transmitting Electrical Energy — 1902 January 18).

The skin effect myth

The dangers of high frequency electrical current are sometimes perceived as being less than at lower frequencies. This is often, but mistakenly, interpreted as being due to skin effect, a phenomenon that tends to inhibit alternating current from flowing inside conducting media. Although skin effect is applicable to good electrical conductors (i.e., metals), the skin depth of human flesh at typical Tesla Coil frequencies is still of the order of 60 inches or more. This means that high frequency currents will still preferentially flow through deeper, better conducting, portions of an experimenter's body such as the circulatory and nervous systems. In reality, a human being's nervous system does not directly sense the flow of potentially dangerous electrical currents above 15–20 kHz. And, since the body no longer provides a warning "shock", novices may touch the output streamers of small Tesla Coils without feeling painful shocks. However, there is anecdotal evidence among Tesla Coil experimenters that temporary tissue damage may still occur as muscle, joint pain, or tingling hours afterward. This is believed to be caused by the damaging effects of internal current flow, and is especially common with continuous wave (CW) solid state or vacuum tube type Tesla Coils.

Large Tesla Coils and Magnifiers can deliver dangerous levels of high frequency current, and they can also develop significantly higher voltages (often 250,000–500,000 volts, or more). Because of the higher voltages, large systems can deliver higher energy, potentially lethal, repetitive high voltage capacitor discharges from their top terminals. Doubling the output voltage quadruples the electrostatic energy stored in the same top terminal. If an unwary experimenter accidentally places himself in path of the high voltage capacitor discharge to ground, the high current electric shock can cause involuntary spasms of major muscle groups, and may induce life-threatening ventricular fibrillation and cardiac arrest. Even lower power vacuum tube or solid state Tesla Coils can deliver RF currents that are capable of causing temporary internal tissue, nerve, or joint damage through Joule heating. In addition, an RF arc can carbonize flesh, causing a painful and dangerous bone-deep RF burn that may take months to heal. Because of these risks, knowledgable experimenters avoid contact with streamers from all but the smallest systems. Professionals usually use other means of protection such as a Faraday Cage or a chainmail suit to prevent dangerous currents from entering their body.

Instances and devices

Missing image
Operating_tesla_coil.jpg
This is a small tesla coil in operation.

Tesla's Colorado Springs laboratory possessed one of the largest Tesla coils ever built, known as the "Magnifying Transmitter". The Magnifying Transmitter is somewhat different from classic 2-coil Tesla coils. A Magnifier uses a 2-coil "driver" to excite the base of a third coil ("Resonator") that is located some distance from the driver. The operating principles of both systems are similar. The world's largest currently existing 2-coil Tesla coil was made by Greg Leyh. It is a 130,000 watt unit, part of a 38 foot tall sculpture. It is owned by Alan Gibb and currently resides in a private sculpture park at Kakanui Point near Auckland, New Zealand. [1] (http://www.lod.org/Projects/electrum/)

The Tesla coil is an early predecessor (along with the induction coil) of a more modern device called a flyback transformer, which provides the voltage needed to power the cathode ray tube used in some televisions and computer monitors. (CRT displays are now slowly being replaced by liquid crystal displays and other technologies.) The disruptive discharge coil remains in common use as the "ignition coil" or "spark coil" in the ignition system of an internal combustion engine. A modern variant of the Tesla coil is also used to power plasma globe sculptures and similar devices.

Popularity

Tesla coils are very popular devices among certain electrical engineers and electronics enthusiasts. Someone who builds Tesla coils as a hobby is called a "Tesla coiler", or simply "coiler". There are even "coiling" conventions where people attend with their home made Tesla coils and other electrical devices of interest.

It should be noted that there are rather significant safety issues regarding coil assembly and operation by hobbyists (including professional engineers). [2] (http://www.pupman.com/safety.htm) Mag. Erwin Kohaut, a physics teacher at the Austrian high school BGRG 12 Rosasgasse in Vienna, Austria, and some students built one of the biggest Tesla coils of Europe. It stands in the cellar of that school.

Low power Tesla Coils are also sometimes used as a high voltage source for Kirlian photography. [3] (http://www.cebunet.com/kirlian/) Tesla coils feature in the Command and Conquer series of strategy computer games, as a weapon on the Soviet side.

See also

Related Tesla Patents

  • "Means for Generating Electric Currents," U.S. Patent No. 514,168, February 6, 1894
  • "Electrical Transformer," Patent No. 593,138, November 2, 1897
  • "Method Of Utilizing Radiant Energy," Patent No. 685,958 November 5, 1901
  • "Method of Signaling," U.S. Patent No. 723,188, Mar. 17, 1903
  • "System of Signaling," U.S. Patent No. 725,605, Apr. 14, 1903
  • "Apparatus for Transmitting Electrical Energy," Jan. 18, 1902, U.S. Patent 1,119,732, Dec. 1, 1914

See also: List of Tesla patents

External links

Patents

Operation and other information

Builders and examples

Further reading and other references

Electrical World

  • "The Development of High Frequency Currents for Practical Application"., The Electrical World, Vol 32, No. 8.
  • "Boundless Space: A Bus Bar". The Electrical World, Vol 32, No. 19.

Other publications

  • Bieniosek, F. M., "Triple Resonance Pulse Transformer Circuit". Review of Scientific Instruments, 61 (6).
  • Corum, J. F., and K. L. Corum, "RF Coils, Helical Resonators and Voltage Magnification by Coherent Spatial Modes". IEEE, 2001.
  • de Queiroz, Antonio Carlos M., "Synthesis of Multiple Resonance Networks". Universidade Federal do Rio de Janerio, Brazil. EE/COPE.
  • Haller, George Francis, and Elmer Tiling Cunningham, "The Tesla high frequency coil, its construction and uses". New York, D. Van Nostrand company, 1910.
  • Hartley, R. V. L., "Oscillations with Non-linear Reactances". Bell Systems Technical Journal, Sun Publishing. 1992.
  • Norrie, H. S., "Induction Coils: How to make, use, and repair them". Norman H. Schneider, 1907, New York. 4th edition.

Patents

  • Armstrong, E. H., Patent US1113149, "Wireless receiving system". 1914.
  • Armstrong, E. H., Patent US1342885, "Method of receiving high frequency oscillation". 1922.
  • Armstrong, E. H., Patent US1424065, "Signalling system". 1922.
  • Leydorf, G. F., Patent US3278937, "Antenna near field coupling system". 1966.de:Tesla-Transformator

ja:テスラコイル pl:Transformator Tesli pt:Bobina de Tesla ru:Трансформатор Тесла

Navigation

  • Art and Cultures
    • Art (https://academickids.com/encyclopedia/index.php/Art)
    • Architecture (https://academickids.com/encyclopedia/index.php/Architecture)
    • Cultures (https://www.academickids.com/encyclopedia/index.php/Cultures)
    • Music (https://www.academickids.com/encyclopedia/index.php/Music)
    • Musical Instruments (http://academickids.com/encyclopedia/index.php/List_of_musical_instruments)
  • Biographies (http://www.academickids.com/encyclopedia/index.php/Biographies)
  • Clipart (http://www.academickids.com/encyclopedia/index.php/Clipart)
  • Geography (http://www.academickids.com/encyclopedia/index.php/Geography)
    • Countries of the World (http://www.academickids.com/encyclopedia/index.php/Countries)
    • Maps (http://www.academickids.com/encyclopedia/index.php/Maps)
    • Flags (http://www.academickids.com/encyclopedia/index.php/Flags)
    • Continents (http://www.academickids.com/encyclopedia/index.php/Continents)
  • History (http://www.academickids.com/encyclopedia/index.php/History)
    • Ancient Civilizations (http://www.academickids.com/encyclopedia/index.php/Ancient_Civilizations)
    • Industrial Revolution (http://www.academickids.com/encyclopedia/index.php/Industrial_Revolution)
    • Middle Ages (http://www.academickids.com/encyclopedia/index.php/Middle_Ages)
    • Prehistory (http://www.academickids.com/encyclopedia/index.php/Prehistory)
    • Renaissance (http://www.academickids.com/encyclopedia/index.php/Renaissance)
    • Timelines (http://www.academickids.com/encyclopedia/index.php/Timelines)
    • United States (http://www.academickids.com/encyclopedia/index.php/United_States)
    • Wars (http://www.academickids.com/encyclopedia/index.php/Wars)
    • World History (http://www.academickids.com/encyclopedia/index.php/History_of_the_world)
  • Human Body (http://www.academickids.com/encyclopedia/index.php/Human_Body)
  • Mathematics (http://www.academickids.com/encyclopedia/index.php/Mathematics)
  • Reference (http://www.academickids.com/encyclopedia/index.php/Reference)
  • Science (http://www.academickids.com/encyclopedia/index.php/Science)
    • Animals (http://www.academickids.com/encyclopedia/index.php/Animals)
    • Aviation (http://www.academickids.com/encyclopedia/index.php/Aviation)
    • Dinosaurs (http://www.academickids.com/encyclopedia/index.php/Dinosaurs)
    • Earth (http://www.academickids.com/encyclopedia/index.php/Earth)
    • Inventions (http://www.academickids.com/encyclopedia/index.php/Inventions)
    • Physical Science (http://www.academickids.com/encyclopedia/index.php/Physical_Science)
    • Plants (http://www.academickids.com/encyclopedia/index.php/Plants)
    • Scientists (http://www.academickids.com/encyclopedia/index.php/Scientists)
  • Social Studies (http://www.academickids.com/encyclopedia/index.php/Social_Studies)
    • Anthropology (http://www.academickids.com/encyclopedia/index.php/Anthropology)
    • Economics (http://www.academickids.com/encyclopedia/index.php/Economics)
    • Government (http://www.academickids.com/encyclopedia/index.php/Government)
    • Religion (http://www.academickids.com/encyclopedia/index.php/Religion)
    • Holidays (http://www.academickids.com/encyclopedia/index.php/Holidays)
  • Space and Astronomy
    • Solar System (http://www.academickids.com/encyclopedia/index.php/Solar_System)
    • Planets (http://www.academickids.com/encyclopedia/index.php/Planets)
  • Sports (http://www.academickids.com/encyclopedia/index.php/Sports)
  • Timelines (http://www.academickids.com/encyclopedia/index.php/Timelines)
  • Weather (http://www.academickids.com/encyclopedia/index.php/Weather)
  • US States (http://www.academickids.com/encyclopedia/index.php/US_States)

Information

  • Home Page (http://academickids.com/encyclopedia/index.php)
  • Contact Us (http://www.academickids.com/encyclopedia/index.php/Contactus)

  • Clip Art (http://classroomclipart.com)
Toolbox
Personal tools